Slope Failure; its Types, Causes, Technical Terms.

Slope Failure.

In this article, you’ll learn the importance of slopes, types of slope failure, causes of slope failure, and definition of its Technical Terms in details.

Importance of Slopes.

Slopes in soils and rocks are ubiquitous in nature and man-made structures.

Highways, dams, levees, canals, and stockpiles are constructed by sloping the lateral faces of the soil because building slopes are generally less expensive than constructing walls.

Natural forces (wind, water, snow, etc.) change the topography of Earth and other planets, often creating unstable slopes.

slope-failure-types

Failures of natural slopes (landslides) and man-made slopes have resulted in much death and destruction, economic losses, and environmental damage.

Some failures are sudden and catastrophic; others are insidious.

Some failures are widespread; others are localized.

Geotechnical engineers have to pay particular attention to geology, surface drainage, groundwater, and the shear strength of soils in assessing slope stability.

However, we are handicapped by the geological variability of soils and methods for obtaining reliable values of shear strength.

The analyses of slope stability are based on simplifying assumptions, and the design of a stable slope relies heavily on experience and careful site investigation.

A slope failure adjacent to a roadway is shown in Figure 16.1. The failed soil mass can move very quickly over large distances. Your job is to prevent such failure.

types-of-slope-failure

Definitions of key Terms in Slope Failure.

Slip or failure zone is a thin zone of soil that reaches the critical state or residual state, resulting in movement of the upper soil mass.

Slip plane or failure plane or slip surface or failure surface is the surface of sliding.

Sliding mass is the mass of soil within the slip plane and the ground surface.

Slope angle is the angle of inclination of a slope to the horizontal. The slope angle is sometimes referred to as a ratio, for example, 2:1 [horizontal (H):vertical (V)].

Porewater pressure ratio is the ratio of porewater force on a slip surface to the total weight of the soil and any external loading.

Read Also: Determination of Particle Size Distribution of Soil by Sieve Analysis.

Types of Slope Failure.

Slope failures depend on the soil type, soil stratification, groundwater, seepage, and the slope geometry.

We will introduce a few types of slope failure that are common in soils.

1. Translational Slide.

Failure of a slope along a weak zone of soil is called a translational slide (Figure 16.2a). The sliding mass can travel long distances before coming to rest.

Translational slides are common in coarse-grained soils.

2. Rotational Slide.

A common type of failure in homogeneous fine-grained soils is a rotational slide that has its point of rotation on an imaginary axis parallel to the slope.

Three types of rotational failure often occur. One type, called a base slide, occurs by an arc engulfing the whole slope.

i. Base Failure.

A soft soil layer resting on a stiff layer of soil is prone to base failure (Figure 16.2b).

ii. Toe Failure.

The second type of rotational failure is the toe slide, whereby the failure surface passes through the toe of the slope (Figure 16.2c).

iii. Slope Failure.

The third type of rotational failure is the slope slide, whereby the failure surface passes through the slope (Figure 16.2d).

3. Flow Slide.

A flow slide occurs when internal and external conditions force a soil to behave like a viscous fluid and flow down even shallow slopes, spreading out in several directions (Figure 16.2e).

The failure surface is ill-defined in flow slides. Multiple failure surfaces usually occur and change continuously as flow proceeds.

Flow slides can occur in dry and wet soils.

4. Block or Wedge Slide.

Block or wedge slides occur when a soil mass is shattered along joints, seams, fissures, and weak zones by forces emanating from adjacent soils.

The shattered mass moves as blocks and wedges down the slope (Figure 16.2f).

What’s next . . . What causes the slope failures that we briefly described above? The causes are many and varied.

In the next section, we will describe some common causes of slope failure.

slope-failure

Causes of Slope Failure.

Slope failures are caused, in general, by natural forces, human misjudgment and activities, and burrowing animals.

We will describe below some of the main factors that provoke slope failures.

1. Erosion.

Water and wind continuously erode natural and man-made slopes. Erosion changes the geometry of the slope (Figure 16.3a), ultimately resulting in slope failure or, more aptly, a landslide.

Rivers and streams continuously scour their banks, undermining their natural or man-made slopes (Figure 16.3b).

2. Rainfall.

Long periods of rainfall saturate, soften, and erode soils. Water enters into existing cracks and may weaken underlying soil layers, leading to slope failure, for example, mud slides (Figure 16.3c).

3. Earthquakes.

Earthquakes induce dynamic forces (Figure 16.3d), especially dynamic shear forces that reduce the shear strength and stiffness of the soil.

Porewater pressures in saturated coarse-grained soils could rise to a value equal to the total mean stress and cause these soils to behave like viscous fluids—a phenomenon
known as dynamic liquefaction.

Structures founded on these soils would collapse; structures buried within them would rise.

The quickness (a few seconds) with which the dynamic forces are induced prevents
even coarse-grained soils from draining the excess porewater pressures. Thus, slope failure in a seismic event often occurs under undrained condition.

Watch the video below for better understanding.

Read Also: Specific Gravity of Soil Test by Pycnometer Method.

4. Geological Features.

Many failures commonly result from unidentified geological features.

A thin seam of silt (a few millimeters thick) under a thick deposit of stiff clay can easily be overlooked in drilling operations,

or one may be careless in assessing borehole logs only to find later that the presence of the silt caused a catastrophic failure.

Sloping, stratified soils are prone to translational slide along weak layers (Figure 16.3e). You must pay particular attention to geological features in assessing slope stability.

5. External Loading.

Loads placed on the crest of a slope (the top of the slope) add to the gravitational load and may cause slope failure (Figure 16.3f).

A load placed at the toe, called a berm, will increase the stability of the slope. Berms are often used to re-mediate problem slopes.

causes-of-slope-failure

6. Construction Activities.

Construction activities near the toe of an existing slope can cause failure because lateral resistance is removed (Figure 16.3g).

We can conveniently divide slope failures due to construction activities into two cases. The first case is the excavated slope and the second case is fill slope.

7. Rapid Drawdown.

Reservoirs can be subjected to rapid drawdown. In this case, the lateral force provided by the water is removed, and the excess porewater pressure does not have enough time to dissipate (Figure 16.3i).

The net effect is that the slope can fail under undrained condition. If the water level in the reservoir remains at low levels and failure did not occur under the undrained condition,

seepage of groundwater would occur, and the additional seepage forces could provoke failure (Figure 16.3j).

slope-failure-causes

THE ESSENTIAL POINTS ARE:

1. Geological features and environmental conditions (e.g., external loads and natural forces) are responsible for most slope failures.

2. The common modes of slope failure in soils are by translation, rotation, flow, and block movements.

Thanks for Reading “Slope Failure, its Types, Causes.” Don’t forget to share it.

Read More: Determination of Field Density Test of Soil by Core Cutter Method.

Leave a Comment